Refer to the help topics in the web application for additional information. The firmware version can be identified in the devices tree in Audio Architect — And also in the Dante Controller Device View under the Status tab. One example would be for the 20 kHz tone to be connected to an analog or Dante receiver input channel on a matrix intercom system. These names can be retained or changed using the editor shown below. Technological advancements include native support, higher channel count, lower latency, and automatic configuration. Note that the Matrix router will allow routing of Unicast flows only. The device shall be powered over Ethernet PoE by an included 802.
Open the presets menu to reveal preset options: save as preset: Saves settings to the device load preset: Opens a configuration from the device import from file: Downloads a preset file from a computer onto the device. This facility is designed to make the channels easily identifiable within Dante Controller. . These bi-directional products interface microphone and line level audio with a Dante network and are packaged in a dual-Decora® form factor. Specifications are subject to change without notice. It provides an intuitive Graphical User Interface allowing the discovery of Dante devices on a network, the setup of audio routing and the monitoring of device status. P48 phantom voltage is supplied to each microphone input.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Network audio expansion shall be provided by the Dante protocol. All our podium mics, all our table mics - everything. Therefore, the entire Dante network is set to slave off the London device. The nominal audio levels of the line input and line output functions can be independently selected. Event Log The event log provides a detailed account of activity from the moment the device is powered on. To change the metering setting, open the Settings menu, select the General tab, and adjust the Metering setting.
When connected to a PoE enabled switch and a local power supply the unit will reserve power from the PoE switch but will be powered by the local supply. Note that the Matrix router will allow routing of Unicast flows only. A list of sales representatives is available online at or by calling 800-237-2041. In Read-Only mode, device parameters can be viewed, but not edited. Plus - digital distribution doesn't require anything in the way of hardware or software expense.
For details on how to load firmware refer to the User Guide associated for each specific product. Network audio expansion shall be provided by the Dante protocol. To protect settings with a password, open the Settings menu and select the General tab. Special software is not required to configure the module. Tip: Use the filter to narrow down results.
Metering is off by default. But more about that in a minute. Audinate also has offices in London and Hong Kong. Get Limiter Status Command String: Indicates if the limiter is currently reducing the signal level. These signals are available both as line-level analog and Dante digital audio transmitter outputs. Cable Requirements Dante supports both Fast Ethernet and Gigabit Ethernet.
Audio connections shall be accessed via rear panel 3. The Dante Controller software application can be downloaded from. This is useful for creating a library of reusable configuration files on computers used for system installation. To do this, open Device View in Dante Controller, select the card you wish to modify in the Device View, and change the sample rate in the Device Config tab. Developed in 2006 by a Sydney-based company named Audinate, Dante builds and improves on previous technologies, such as and. Dante is compatible with standard Ethernet switches and routers. Each output provides a switch to set the output to balanced professional or unbalanced consumer level.
The flash automatically turns off after 30 seconds. Mic pre-amp gain 0, 11. Use the Dante Controller to check Dante device sample rates. For 96kHz 24bit audio the channel capacity is halved. Using the Dante protocol, Symetrix transmits and receives uncompressed full bandwidth audio with up to 32 bits of resolution at a 48kHz sample rate.
The duplicate audio streams are transmitted simultaneously, so the secondary network automatically prevents any audio interruption or loss if a connectivity problem occurs on the primary network. The meters, located on the front panel, display the level of the audio signals associated with the two line inputs and two line outputs. It cuts my set-up time tons. These are then converted into analog outputs. For contact information please visit www. Dante Manufacturer Info Manufacturer Audinate Pty.
Rack-mount options are also available allowing one or two units to be mounted in one space 1U of a standard 19-inch rack enclosure. The Model 44D will then provide two analog input and two analog output interfaces for use in a variety of applications. Presets are a snapshot of the current audio routing configuration for backup or use at a later time. One switch enables or disables P48 phantom for that input; the second switch selects the mic or line gain range; the third switch sets the gain. Note: The Q and width parameters affect the equalization curve in the same way.